NEW! Millermatic 141 W/Auto Set 110 Volt MIG Welder With Cart Part #951601
![](https://www.weldersupply.com/Content/files/ProductImages/MillerLogo_THL.png)
Welding type:
![Mig](https://www.weldersupply.com/Content/files/ProductImages/C-9-MigWelders_THL.png)
Mig
Power supply:
![110V](https://www.weldersupply.com/Content/files/ProductImages/C-647-110V_THL.png)
110V
Material type:
![Mild Steel](https://www.weldersupply.com/Content/files/ProductImages/643-NewCat-MildSteel_THL.png)
Mild Steel
![Stainless Steel](https://www.weldersupply.com/Content/files/ProductImages/643-NewCat-Stainless_THL.png)
Stainless Steel
![Aluminum](https://www.weldersupply.com/Content/files/ProductImages/643-NewCat-Aluminum_THL.png)
Welding has never been easier since the introduction of the Millermatic 141 MIG welder. It's an all-in-one wire welder for welding 24 gauge- 3/16 in. (0.8-4.8mm) mild steel. This welder features an Auto-Set program to help you get the settings right from the very beginning. You also don’t need to worry about overheating the machine, since it has an automatic shut off Thermal Overload Protection. Welding has never been easier!
It features Miller's breakthrough Auto-Set system, which automatically sets your welder to the proper parameters. All you have to do is set the wire diameter and weld parameters and you are ready to start welding. You can also set the weld parameters manually for broader applications.
How often have you started a project and it spatters all over? The Millermatic 140 features the NEW Smooth-Start patent-pending technology. It provides a smooth, spatter-free start. No more pop-gun starts or spatter to clean up.
Setup is easier and faster than ever. The durable cast aluminum feed head incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob. If the airflow is blocked or the duty cycle is exceeded, the Thermal Overload Protection shuts down the unit. If the tip is shorted to the work, the "Tip Saver" short circuit protection shuts down output. The trigger reset permits quick reset right from the torch rather than the unit. The wire is electronically "cold" until the trigger is pulled, using the standard built-in solid-state contactor circuit. This makes the unit easier and safer to position the torch to work before starting to weld.
Switching from solid to flux-cored wires has never been easier. The easy access to output studs provides convenient polarity changeover, and the self-resetting motor protection circuit eliminates the need to find and replaces fuses.
Millermatic 141 MIG welder Features:
WHAT'S INCLUDED
View all Miller Welding Machines
Other Versions:
907612 110 Volt Mig Welder
General Specifications |
|
Input Power | Requires 1-Phase power 115 V, 20 Amps, 60 Hz |
Rated Output | 90 Amps at 18 VDC, 20% duty cycle |
Welding Amperage Range | 30 - 140 Amps |
Wire Speed | 15 - 360 IPM (.40 - 9.1 m/min) |
Net Weight | 51lb (27.3kg) |
WireDiameter Capacity | .024 - .030 in (0.6 - 0.8 mm) Solid Steel .024 - .030 in (0.6 - 0.8 mm) Stainless .030 - .035 in (0.8 - 1.2 mm) Flux Cored |
MaxSpoolSize Capacity | 8 in (203 mm) |
SHIPPING DIMENSIONS |
|
Height: | 18.00 Inches |
Width: | 22.00 Inches |
Length: | 38.00 Inches |
Weight: | 86 Lb(s) 0 Oz |
Remove guide by pressing on barbed area or cutting off one end near housing and pulling it out of hole.
Push new guide into hole from rear until it snaps in place.
Locate open slot and push drive roll completely over retaining pin, then rotate drive roll to desired slot.